You throw your load in the dryer, set the timer, and go. You go back to grab your work pants and prepare only to find that the dryer is not working as it should. Here are some dryer repair tips to help get your dryer working again.
If it doesn’t work at all, there are a few things you can try.
Make sure the power cord is plugged in. Unplug it and plug it in again. Check the circuit breakers to make sure they have not tripped or that a fuse has not blown. You can also use a voltmeter to check the plug to make sure there is power to the plug.
On the door there is a switch or sensor that when closing the door presses against a lever which then activates a door switch that allows the dryer to turn on. If that lever breaks, the switch cannot be activated and the dryer cannot start. You may need to replace this lever.
Almost all dryers on the market have a thermal fuse. This fuse will blow if the dryer overheats. When this happens, one of two things happens. The dryer stops working completely or works but does not emit heat. You will usually find this fuse under the ventilation duct inside the dryer. If the fuse is blown, you will want to replace it.
Occasionally a dryer timer can be faulty, so even if you have turned on the dryer it does not recognize movement and therefore the dryer will not turn on the dryer repair.
If it’s not hot, there are a few things you can try.
Gas valve coils
If the igniter ignites but then turns off before it ignites, the gas is likely due to a bad coil. Replace all coils; there are usually at least a couple and sometimes more. The gas valve may also need to be replaced.
If the dryer overheats, the thermal fuse will blow, which means that your dryer will not work at all or it will work but will not shed heat. Look at the ventilation duct inside the dryer; This is where you will normally find the fuse. Replace it.
The lighter may be defective or because it is so fragile that it can be easily broken. You should never touch the lighter except the ceramic part.
If your dryer is blowing heat but it takes too long to dry your clothes, there are a few things you can check.
Check the vent hose and vent just to make sure there are no obstructions. Lint collects inside the dryer and, if you don’t clean it regularly, it lands on the vent pipe, reducing the efficiency of the dryer and increasing the risk of fire.
Easy and Inexpensive Dryer Repair Solutions
You rely on your clothes dryer to help you manage your normal routine, so when it malfunctions or breaks down, the downside can be profound.
We have all been there at least once. You have a ton of chores to do and laundry is at the top of your list. You think, “why not kill two birds with one stone?” So he loads the dryer, sets the timer, and takes care of his other responsibilities. Forty-five minutes later, you’re back in the laundry room only to be faced with a pile of cold, damp clothes. Few things are that frustrating. If your dryer isn’t working properly, it can seriously hamper your daily routine. Who has time to load a pile of dirty clothes from one side of the laundry room to the other or to wait for the clothes to air dry? The good news is that there are a number of simple steps you can take to restore your dryer to full functionality without costing you a fortune.
The first step when it comes to any type of appliance dryer repair is determining what exactly is causing the problem. Does the dryer start? Does it heat up and spin? Are you taking too long to try on your clothes? The answers to these questions will help you identify the source of the problem. Here are some simple troubleshooting steps:
- Make sure the dryer is plugged in – Sure, it might sound like common sense, but complaints about dryer performance that end up plugging the cord into the outlet are more common than you might think.
- Check and replace blown fuses – Depending on the age and model, your dryer can consume a lot of energy. This can lead to blown fuses and tripped circuits, especially in homes with older electrical systems. It should be relatively easy to replace the fuse or reset the circuit breaker, but if the problem recurs, you should contact a professional electrician.
- Clean the lint trap – If your clothes take a long time to dry, the cause may be a full lint trap. A clogged lint filter can also cause the dryer to overheat, putting your appliance at risk of fire. To avoid potential hazards and keep your dryer operating at optimum levels, it is important to clean the lint screen immediately after each load.
- Check the dryer hose and exhaust vent – If your lint trap is clean and clothes are still taking a long time to dry, you may need to clean the dryer hose and exhaust vent. Over time, lint can build up, blocking the hose or preventing the escape trap from opening. You can use a vacuum cleaner and / or a long-handled bristle brush to clean up any excessive buildup of lint.
If all else fails, consult your dryer repair manual. Most dryer manufacturers include a list of common troubleshooting steps and dryer repair problems. Your repair manual may also include part numbers and descriptions of commonly replaced parts, such as straps and knobs. Additionally, most dryer repair manuals break down the steps for proper maintenance, such as vent cleaning and electrical specifications, so you can keep your dryer running in the best possible condition.